nsumption Hub-1 - for dc-coupled systems ====
{{:assistants:self-consumption-hub-1-welcome.png?direct&150 }} {{:assistants:self-consumption-hub-1-policy.png?direct&150 }}
... mption Hub-2 v3 - for ac-coupled systems ====
{{:assistants:self-consumption-hub-2-v3-welcome.png?direct&150 }} {{:assistants:self-consumption-hub-2-v3-policy.png?direct&150 }... r hardware with new microprocessor (26 or 27).
[[assistants:hub1_and_hub2_notes|]]
==== DEPRECATED Self-cons... been deprecated in favor of [[ess:start|ESS]].
[[assistants:hub1_and_hub2_notes|]]
==== DEPRECATED Self-cons
better understanding of the possibilities, read [[assistants:overview_of_available_assistants|the list of available assistants]].
==== I don't see the Assistants tab, how do I... _an_assistant|How to update an Assistant]]
* [[:assistants:overview_of_available_assistants|Overview of available Assistants]]
* [[:assistants:ignore_ac_input_using_the_generator_assistant|Ignore AC Input using the Generator start/s... sing_bmv_soc_in_a_vebus_assistant_setup]]
* {{ :assistants:3299-virtual-switch-ignore-ac-lesson.pdf |Virtual
ure3
- It will give a notification when new Assistants are available: {{ :assistants:veconfig3-assistants-update-available.png?nolink& }}
- Connect VECon... re is an update for one or more of the configured Assistants, a warning will appear.{{ :assistants:marked.png?nolink& }}
- All Assistants that can be updated will be marked with a star.
- Right click the assistant, and press update{{ :assistants:rightclick_1.png?nolink& }}
- VEConfigure3 will
uter, connect to the Victron product and open the Assistants tab. Don't see the assistants tab? See [[:assistants:start#i_don_t_see_the_assistants_tab_how_do_i_get_it|here]].
Then, from the drop ... :02.png}}
The assistant will appear in the ‘Used assistants’ box and it will be in italics, as it has not bee
e required in some installation types. When using assistants with multiple units, some assistants are required to be loaded onto all units in the system individually, and some assistants are able to be just loaded onto some or one of th... rdware interface connections.
With all the other Assistants: genset start/stop, relay locker etcetera, a uniq
use the the [[https://www.victronenergy.com/live/assistants:overview_of_available_assistants#deprecated_self-consumption_hub-2_v3_-_for_ac-cou... -consumption Hub-2 v3 assistant.
There are three assistants used:
- Generator start and stop, which is not ... inverter mode.
Note that the order in which the assistants are is important!
{{ :ignore_ac_input_assistant
inverters/grid codes.
More information on adding Assistants is [[assistants:how_to_add_and_configure_an_assistant|here]].
==... s locked to 53 Hz and does not resume ====
See [[:assistants:pv-inverter-support#q1_the_system_is_locked_to_53
roduct available? No problem, it is possible to [[assistants:start#how_can_i_play_around_with_assistants_without_using_real_hardware|go through the pages
ts|Update the Inverter/charger firmware]] - (2) [[assistants:how_to_update_an_assistant|Update the Assistants]] - (3) [[ccgx:firmware_updating|Update the GX De
approximately 85 seconds per unit; and in case [[assistants:start|VEConfigure Assistants]] are used; ten it will take longer: writing an Assistants takes anything between a few and 40 seconds per un... guration. Some settings though, such as a changed Assistants configuration, will cause the inverter/charger to
i-soc.png?nolink |}}
==== Load and configure the Assistants ====
The next step is to load 3 assistants in the Multi.
1st assistant "programmable relay" to give the con... neral flag to ignore AC input 1
With these three assistants used together AC input 1 will be used (not ignore... output of the Multi, they can use the above three assistants, plus at the bottom position add the "PV Inverter
====== Self-consumption hub-1 ======
{{:assistants:self-consumption-hub-1-welcome.png?nolink|}}
{{:assistants:self-consumption-hub-1-policy.png?nolink|}}
====... attro) and one or more VE.Direct chargers]]
* [[assistants:hub1_and_hub2_notes|]]
===== Frequently asked qu
y in the evening and night. Easy configuration in Assistants and on the Color Control GX.
- Advanced \\ Same... he PV Inverter Assistant to the list of installed Assistants in VEConfigure.
===== 4. Single vs multi phase in... istant. Instructions on how to add an Assistant [[assistants:how_to_add_and_configure_an_assistant|here]].
No
on the ColorControl
2. Add and configure the assistants: 'General flag user' and 'Programmable relay'
... tings =====
To make it work add and configure the assistants: 'General flag user' and Programmable relay \\
Mo... u need to 2 instances of the 'Programmable relay' assistants. 1 to set the flag and 1 to clear the flag. \\
*
not supported.
Switch to the next register tab "Assistants":
{{:drafts:ecomulti-0059.png?nolink&500}}
Add ... or is completely configured. In the register tab "Assistants" add the "Self consumption Hub-2v3":
{{:drafts:e
