Differences

This shows you the differences between two versions of the page.

--- mppt-error-codes [2017-10-20 06:23] – [Err 34 - PV over-current] mvader
+++ mppt-error-codes [2019-05-06 13:46] – rvanzundert
@@ Line 33: / Line 33: @@
 ==== Err 18 - Controller over-current ====
 This error will auto-reset.
-Disconnect the charge controller from all power-sources, wait 3 minutes, and power up again.
+If the error does not auto-reset disconnect the charge controller from all power-sources, wait 3 minutes, and power up again. If the error persists the charge controller is probably faulty.
-If the error persists the charge controller is probably faulty.
+A cause for this error can be switching on a very large load on the battery side.
 ==== Err 20 - Maximum Bulk-time exceeded ====
@@ Line 58: / Line 58: @@
 This error will auto-reset.
+==== Err 28 - Power stage issue ====
+This error will not auto-reset.
+Disconnect all wires, and then reconnect all wires. If the error persists the charge controller is probably faulty.
 ==== Err 33 - PV over-voltage ====
@@ Line 67: / Line 73: @@
 Disconnect the charger from all power-sources, wait 3 minutes, and power-up again. If the error persists the controller is probably faulty, contact your dealer.
-==== Err 38 - Input shutdown due to battery over-voltage ====
+==== Err 38, Err 39 - PV Input shutdown ====
-To protect the battery from over-charging the panel input is shut down. To recover from this condition first disconnect the solar panels and disconnect the battery. Wait for 3 minutes reconnect the battery first and next the panels.
+To protect the battery from over-charging the panel input is shorted.
-A common reason for this error to occur is that the Battery voltage (12/24/48V) is set, or auto-detected, incorrectly.
+Possible reasons for this error to occur:
+	* The Battery voltage (12/24/48V) is set, or auto-detected, incorrectly. Use VictronConnect to disable auto-detect and set the Battery Voltage to a fixed voltage.
+	* There is another device connected to the battery, which is configured to a higher voltage. For example a MultiPlus, configured to equalise at 17 Volts, while in the MPPT this is not configured.
+	* The battery is disconnected using a manual switch. Ideally the charger should be switched off before disconnecting the battery, this avoids a voltage overshoot on the charger output. If necessary the voltage trip-level for the PV Short protection can be increased by raising the Equalization voltage set-point (note: equalization does not have to be enabled in this case).
+	* The battery is disconnected using a Lithium charge relay connected to the “allow-to-charge” output of a BMS. Consider wiring this signal to the Remote terminal of the charger instead. This shuts down the charger gracefully without creating a voltage overshoot.
-Use VictronConnect to disable auto-detect and set the BatteryVoltage to a fixed voltage.
+Error recovery:
+	* Error 38: First disconnect the solar panels and disconnect the battery. Wait for 3 minutes, then reconnect the battery first and next the panels.
+	* Error 39: The charger will automatically resume operation once the battery voltage drops below the float level for 1 minute.
 If the error persists the charge controller is probably faulty.
 ==== Information 65 - Communication warning ====
 Communication with one of the paralleled controllers was lost. To clear the warning, switch the controller off and back on
@@ Line 97: / Line 110: @@
 Note that (solar-)chargers automatically configure themselves to be BMS-controlled when they are connected to one; either direct or via a Color Control GX or Venus GX.
+==== Err 68 - Network misconfigured ====
+The charger detects multiple conflicting network sources trying to take control of the charger.
+All Smart Solar charger models:
+  * If the charger is connected to a Venus GX device that takes control of the charger (by sending Charge Voltage Limits to the unit), the charger cannot not be joined to a VE.Smart network as well. In VictronConnect go to settings "VE.Smart networking" and choose "Leave network".
+VE.CAN Smart Solar chargers only:
+  * If the charger is connected via VE.CAN to a Venus GX device do not install a VE.Direct cable to a Venus GX device as well. Either disconnect the VE.CAN cable or the VE.Direct cable.
+Once the conflict is resolved the error will disappear and the charger will resume normal operation, usually within a minute.
 ==== Err 114 - CPU temperature too high ====
@@ Line 104: / Line 133: @@
 ==== Err 116 - Calibration data lost ====
-The unit is faulty, contact your dealer for a replacement.
+If the unit does not work and error 116 pops up as the active error the unit is faulty, contact your dealer for a replacement.
+If the error is only present in the history data and the unit operates normally this error can be ignored safely. Explanation: when the units power up for the very first time in the factory, it does not have calibration data and an error 116 is logged. Obviously this should have been cleared, but in the beginning units left the factory with this message still in the history data.
 ==== Err 119 - Settings data lost ====
@@ Line 114: / Line 146: @@
   - wait 3 minutes, and power up again.
   - Reconfigure the charger.
 ===== DISQUS =====
 ~~DISQUS~~