Differences

This shows you the differences between two versions of the page.

--- assistants:overview_of_available_assistants [2016-12-11 21:11] – [Self-consumption Hub-4] mvader
+++ assistants:overview_of_available_assistants [2022-06-01 13:41] (current) – Fixed typo. fredhen
@@ Line 10: / Line 10: @@
 {{:assistants:ess-first-page.png?direct&150 }}
-[[ess:start|]]
+For Energy Storage Systems (ESS). The Assistant manages the prioritising of Solar Power.
-Only for hardware with new microprocessor (26 or 27).
+[[ess:start|Documentation]].
-==== Self-consumption Hub-1 - for dc-coupled systems ====
+==== PV Inverter support ====
+{{:assistants:pvinvertersupport.png?direct&150 }}
+Use this Assistant in Off-grid systems that have AC-Coupled solar power: a grid-tie PV inverter connected to the AC out of a Multi or Quattro inverter/charger.
+[[:assistants:pv-inverter-support|Documentation]].
+==== DEPRECATED Self-consumption Hub-1 - for dc-coupled systems ====
 {{:assistants:self-consumption-hub-1-welcome.png?direct&150 }} {{:assistants:self-consumption-hub-1-policy.png?direct&150 }}
-[[:assistants:self_consumption_hub-1|Self-consumption hub-1 Assistant]].
+Note that Hub-1 is deprecated in favor of [[ess:start|ESS]].
+[[:assistants:self_consumption_hub-1|Hub-1 Assistant documentation]].
+Hub-1 is only for hardware with new microprocessor (26 or 27).
-Only for hardware with new microprocessor (26 or 27).
+[[assistants:hub1_and_hub2_notes|]]
-==== Self-consumption Hub-2 v3 - for ac-coupled systems ====
+==== DEPRECATED Self-consumption Hub-2 v3 - for ac-coupled systems ====
 {{:assistants:self-consumption-hub-2-v3-welcome.png?direct&150 }} {{:assistants:self-consumption-hub-2-v3-policy.png?direct&150 }}
@@ Line 28: / Line 42: @@
 Take note of the [[:ac_coupling:start|factor 1.0 rule]].
-See also our [[https://www.victronenergy.com/blog/2014/07/29/self-consumption-hub-2-v3-assistant-a-major-update/|blog post on the Self-consumption Hub-2 Assistant]].
+Deprecated in favor of [[ess:start|ESS]].
 Only for hardware with new microprocessor (26 or 27).
-==== Self-consumption Hub-2 v2 - for ac-coupled systems ====
+[[assistants:hub1_and_hub2_notes|]]
+==== DEPRECATED Self-consumption Hub-2 v2 - for ac-coupled systems ====
 Use only on hardware with old microprocessor (19 or 20). On newer systems, use the version 3 instead, see above.
@@ Line 38: / Line 54: @@
 Take note of the [[:ac_coupling:start|factor 1.0 rule]].
-==== Self-consumption Hub-4 ====
+Note that all Hub-2 Assistant versions have been deprecated in favor of [[ess:start|ESS]].
+[[assistants:hub1_and_hub2_notes|]]
+==== DEPRECATED Self-consumption Hub-4 ====
 {{:assistants:self-consumption-hub-4-welcome.png?direct&150 |}}
@@ Line 48: / Line 68: @@
 Only for hardware with new microprocessor (26 or 27).
-==== PV Inverter support ====
-{{:assistants:pvinvertersupport.png?direct&150 }}
-Used in:
-  * Off-grid PV installs
-  * Systems using the Hub-4 Assistant with a PV Inverter connected to the output of the Multi or Quattro. Note that Hub-4 has been deprecated: use [[ess:start|ESS]] instead. And PV Inverter Support / frequency shifting is built into ESS: no need to add the PV Inverter Support Assistant as well.
-Take note of the [[:ac_coupling:start|factor 1.0 rule]].
@@ Line 63: / Line 74: @@
 ==== Generator start and stop ====
-{{:assistants:c000c5d0534684c578209f4e3445bef0.png?direct&150 }}Automatically start and stop a generator based on battery state of charge and actual load of a system. Note that automatic genset start/stop functionality is also available on the Virtual switch tab, which is easier to configure and does not require uploading another type of firmware. See the PDF [[https://www.victronenergy.com/upload/documents/manual-VE.Bus-firmware-versions-explained-EN.pdf|VE.Bus firmware versions explained]] for more information about the different firmware types.
+{{:assistants:c000c5d0534684c578209f4e3445bef0.png?direct&150 }}Automatically start and stop a generator based on battery state of charge and actual load of a system. Note that automatic genset start/stop functionality is also available on the Virtual switch tab in VEConfigure, which is easier to work with.
+This is one of the available options to automatically start and stop a generator using Victron equipment. See the [[auto-generator-start-stop:start|]] document for an overview of all options. More general information about  using a generator in combination with Victron is available [[:multiplus_faq|here]].
 This Generator start and stop Assistant is also the one to use to [[:assistants:ignore_ac_input_using_the_generator_assistant|configure Ignore AC Input using Assistants]].
@@ Line 69: / Line 82: @@
 ==== AC Current sensor ====
-{{:assistants:ac_current_sensor.png?direct&150 }}Reads PV Inverter current, using an AC Current sensor (CSE000100000), connected to a VE.Bus product. More information available in the [[https://www.victronenergy.com/upload/documents/Manual-AC-Current-sensor-EN.pdf|AC Current sensor manual]].
+{{:assistants:ac_current_sensor.png?direct&150 }}Reads PV Inverter current, using an AC Current sensor (CSE000100000), connected to a VE.Bus product. More information available in the [[https://www.victronenergy.com/live/ac_current_sensor:start|AC Current sensor manual]].
 ==== Silence fan ====
@@ Line 91: / Line 104: @@
 {{:assistants:85fa9bbfa1ab60f30e018fae30f2b3c2.png?direct&150 }}Used to wire an emergency stop button to a VE.Bus system.
-==== VE.Bus BMS support ====
+==== DEPRECATED VE.Bus BMS support ====
-{{:assistants:d4c13a7dba68a0ac07ef946122785e57.png?direct&150 }}Required in combination with a [[https://www.victronenergy.com/batteries/lithium-battery-12,8v|VE.Bus BMS, used with our 12.8 V Lithium batteries]]. This Assistant communicates with the BMS and controls the Multi based on the BMS measurements.
+{{:assistants:d4c13a7dba68a0ac07ef946122785e57.png?direct&150 }}
-==== Lynx Ion BMS support ====
+Deprecated: per VE.Bus firmware version 489, this Assistant is no longer required. When installing a system with VE.Bus BMS, our advice is to first update the firmware of the inverter, using VictronConnect, and thereafter do the configuration. No Assistant needed.
-{{:assistants:020b6a4a7ba5fc55edf4bdf7307dd0ed.png?direct&150 }}Required in combination with a [[https://www.victronenergy.com/batteries/lithium-battery-24v-180ah|Lynx Ion BMS, used with our 24 V 180 Ah Lithium system]]. This Assistant can also be used to control the Multi with a third party Lithium system including BMS. See our PDF [[https://www.victronenergy.com/upload/documents/Manual-Connecting-other-lithium-battery-systems-to-Multis-and-Quattros-EN.pdf|Connecting other lithium battery systems to Multis and Quattros]] for more information.
+Required in combination with a [[https://www.victronenergy.com/batteries/lithium-battery-12,8v|VE.Bus BMS, used with our 12.8 V Lithium batteries]]. This Assistant communicates with the BMS and controls the Multi based on the BMS measurements.
+==== Two-Signal BMS support (previously called Lynx Ion BMS support) ====
+{{:assistants:020b6a4a7ba5fc55edf4bdf7307dd0ed.png?direct&150 }}Required in combination with a Lynx Ion BMS, used with our 24 V 180 Ah Lithium system. This Assistant can also be used to control the Multi with a third party Lithium system including BMS. See our PDF [[https://www.victronenergy.com/upload/documents/Manual-Connecting-other-lithium-battery-systems-to-Multis-and-Quattros-EN.pdf|Connecting other lithium battery systems to Multis and Quattros]] for more information.
@@ Line 114: / Line 131: @@
 {{:assistants:6e528aa50cd09a1740b2056370552464.png?direct&150 }}
+===== DISQUS =====
 ~~DISQUS~~