User Tools

Site Tools


victronconnect:mppt-solarchargers

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
victronconnect:mppt-solarchargers [2019-06-25 16:06]
mvader
victronconnect:mppt-solarchargers [2019-09-28 14:19] (current)
guy_stewart [3. HISTORY - Thirty-day Graphic]
Line 53: Line 53:
  
 (If you are operating an [[http://​https://​www.victronenergy.com/​live/​ess:​design-installation-manual|ESS]] (Energy Storage System) the charge time for this will be included in the '​Bulk'​ reading.) ​ (If you are operating an [[http://​https://​www.victronenergy.com/​live/​ess:​design-installation-manual|ESS]] (Energy Storage System) the charge time for this will be included in the '​Bulk'​ reading.) ​
 +
 +It is possible to export the history by clicking the three connected dots at the top right of the history screen. ​
  
 **Battery Voltage**\\ ​ **Battery Voltage**\\ ​
Line 301: Line 303:
 {{:​victronconnect:​vc4_iphone_bluesolar_rxportsettings.png?​direct&​150|VictronConnect - MPPT RX port settings}} {{:​victronconnect:​vc4_iphone_bluesolar_rxportsettings.png?​direct&​150|VictronConnect - MPPT RX port settings}}
  
-The Rx pin on the VE.Direct connector can be used for other functions. This functionality was introduced in firmware version 1.17 and applies to the 10A, 15A and 20A chargers with a load output.+The Rx pin on the VE.Direct connector can be used for other functions. This functionality was introduced in firmware version 1.17.
 Available options: Available options:
  
   - **Remote on/off (This is the default setting on all larger models)**. This setting allows remote on/off control: (0V = switch charger off, +5V (or a signal sent via VE.Direct communication) = switch charger on). An example of this operation is when the unit is connected to a [[https://​www.victronenergy.com/​accessories/​ve-bus-bms|VE.BUS BMS]] (using a [[https://​www.victronenergy.com/​accessories/​ve-direct-non-inverting-remote-on-off-cable|VE.Direct non inverting remote on-off cable, ASS030550300]]).   - **Remote on/off (This is the default setting on all larger models)**. This setting allows remote on/off control: (0V = switch charger off, +5V (or a signal sent via VE.Direct communication) = switch charger on). An example of this operation is when the unit is connected to a [[https://​www.victronenergy.com/​accessories/​ve-bus-bms|VE.BUS BMS]] (using a [[https://​www.victronenergy.com/​accessories/​ve-direct-non-inverting-remote-on-off-cable|VE.Direct non inverting remote on-off cable, ASS030550300]]).
-  - **Load output configuration (This is the default setting on the following models: 75/10, 75/15, 100/15 and 100/20)**. The Tx pin can be used to place a jumper to select load output operation. See Load output chapter (**4.2** above) for details.+  - **Load output configuration (This is the default setting on the following models: 75/10, 75/15, 100/15 and 100/20)**. The Tx pin can be used to place a jumper to select load output operation. See Load output chapter (**4.2** above) for details. This only applies to the 10A, 15A and 20A chargers with a load output.
   - **Load output on/off inverted** This setting reverses the load output on/off control: (0V = switch load output on, +5V = switch load output off)   - **Load output on/off inverted** This setting reverses the load output on/off control: (0V = switch load output on, +5V = switch load output off)
   - **Load output on/off normal** This setting allows load output on/off control: (0V = switch load output off, +5V = switch load output on)   - **Load output on/off normal** This setting allows load output on/off control: (0V = switch load output off, +5V = switch load output on)
victronconnect/mppt-solarchargers.1561471592.txt.gz · Last modified: 2019-06-25 16:06 by mvader