venus-os:mfd-garmin
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
venus-os:mfd-garmin [2019-02-21 13:05] – mvader | venus-os:mfd-garmin [2020-06-22 09:27] – [4.2. Networking] mbosma | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== | + | ====== Garmin |
- | Garmin themselves calls this technology OneHelm. | ||
- | https://www.garmin.com/ | + | ===== 1. Introduction ===== |
- | ==== Comptibility ==== | + | This document explains how to connect to Garmin MFDs using an Ethernet connection. |
+ | The integration technology used is called [[https:// | ||
- | OneHelm is currently available for the GPSMAP® 8400/8600 MFD series. | + | Make sure to also study the [[https:// |
- | ==== Wiring ==== | + | Note that there is an alternative method to connect, which is NMEA2000. See the [[https:// |
- | an adapter is necessary: | + | ===== 2. Compatibility ===== |
- | - Marine Network Cables - 6ft - PART NUMBER 010-10550-00 | + | OneHelm is currently available for the following models: |
- | | + | |
- | | + | |
- | - Marine Network Cables - 500ft - PART NUMBER 010-10647-01 | + | |
- | ==== Networking ==== | + | Also, Active Captain is supported. This screenshot shows ActiveCaptain, |
- | Needs to be done with ethernet. Not wifi. | + | {{: |
- | (DHCP server op de Garmin) | + | ===== 3. Wiring ===== |
+ | The Garmin needs to be connected to the [[https:// | ||
- | ==== Usage ==== | + | * Marine Network Cables - 6ft - PART NUMBER 010-10550-00 |
+ | * Marine Network Cables - 20ft - PART NUMBER 010-10551-00 | ||
+ | * Marine Network Cables - 40ft - PART NUMBER 010-10552-00 | ||
+ | * Marine Network Cables - 500ft - PART NUMBER 010-10647-01 | ||
+ | |||
+ | |||
+ | ===== 4. Configuration | ||
+ | |||
+ | ==== 4.1. GX device settings ==== | ||
+ | |||
+ | - Go to //Settings -> Services//, and there enable both //MQTT on LAN (SSL)// and //MQTT on LAN (Plaintext)// | ||
+ | - Go to //Settings -> System Setup -> Scroll to the bottom -> Marine MFD App configuration// | ||
+ | - For boats; and other applications with DC loads such as lighting and a Battery Monitor installed, make sure to enable the "Has DC system setting" | ||
+ | |||
+ | ==== 4.2. Networking ==== | ||
+ | No special networking settings are necessary. Not on the Garmin; and not on the Victron GX Device. | ||
+ | |||
+ | The Garmin MFDs run a DHCP server; and the [[https:// | ||
+ | |||
+ | To connect the GX Device to the internet and the [[https:// | ||
+ | |||
+ | :!: Connecting a Garmin MFD to a network router over Ethernet leads to IP address conflicts, due to the integrated DHCP server. | ||
+ | |||
+ | :!: It is not possible to use a [[https:// | ||
+ | |||
+ | ===== 5. Configuring Multiple Battery Monitors ===== | ||
+ | |||
+ | {{youtube> | ||
+ | |||
+ | |||
+ | ===== 6. Step by Step ===== | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
- | Screenshots |
venus-os/mfd-garmin.txt · Last modified: 2023-06-22 19:35 by sloges