Differences

This shows you the differences between two versions of the page.

--- ccgx:start [2019-10-03 13:32] – [5.4 Trouble shooting data logging] mvader
+++ ccgx:start [2019-10-18 10:41] – [6.1 Introduction & requirements] mvader
@@ Line 335: / Line 335: @@
 |Enable password check | Choose password to allow remote console access.||
 |Enable on VRM |No|Enabling on VRM will allow connection to the CCGX from anywhere via the VRM portal. [[vrm_portal:troubleshooting_ccgx_vrm_connectivity#trouble_shooting_remote_console_on_vrm|Trouble shooting Remote Console on VRM]]|
-|Enable on LAN |No|Enabling will allow direct connection to the CCGX by typing it's IP address into a web browser. Only Enable this function on trusted networks. Disable password check, or set password first|
+|Enable on LAN |No|Enabling will allow direct connection to the CCGX by typing its IP address or Venus.local into a web browser, or in VictronConnect when connected to the same network. Only Enable this function on trusted networks. Disable password check, or set password first|
 |**System setup** |||
 |AC input 1 |Generator |Select Generator or Grid. (We will shortly be adding the setting 'Shore power' instead of grid.) |
@@ Line 569: / Line 569: @@
 The AC supply, either Generator or Grid, to a three phase inverter/charger system needs to be in the correct rotation, also known as sequence. If not, then the Inverter/chargers will not accept the AC supply and remain in Inverter mode.
-The ''Phase rotation warning'' will be raised in such case. To resolve the issue, change the wiring on the AC input: swap either one of the phases, effectively changing the rotation from ''L3 -> L2 -> L1'' to ''L1 -> L2 -> L3''.
+The ''Phase rotation warning'' will be raised in such case. To resolve the issue, change the wiring on the AC input: swap either one of the phases, effectively changing the rotation from ''L3 -> L2 -> L1'' to ''L1 -> L2 -> L3''. Or reprogram the Multis and modify the phase assigned to match the wiring.
 On the GX device itself, the warning will be popup as a notification on the GUI:
@@ Line 904: / Line 904: @@
 https://www.youtube.com/watch?v=RWdEQfYZKEs
+[[https://www.youtube.com/watch?v=RWdEQfYZKEs|{{:ccgx:glass_bridge_example.jpg?direct&400|}}]]
 Functionalities:
@@ Line 910: / Line 912: @@
   * Monitor battery status for one or more batteries. By using the voltage of for example battery chargers, it can also visualise secondary batteries such as Generator starter batteries.
   * Monitor the power conversion equipment: chargers, inverters, inverter/chargers.
+  * Monitor solar production from an MPPT Solar Charger.
   * Monitor AC loads, and DC loads.
   * Control shore power input current limit.
@@ Line 915: / Line 918: @@
   * Optionally open the Victron Remote Console panel; allowing access to further parameters.
-Power equipment compatibility:
+Victron equipment compatibility:
   * All Victron inverter/chargers: From a 500VA single phase device up to a large 180kVA three phase-system, including Multis, Quattros, 230VAC and 120VAC models.
-Battery Monitors: BMV-700, BMV-702, BMV-712 and newer, Lynx Shunt VE.Can, Lynx Ion BMS.
+  * Battery Monitors: BMV-700, BMV-702, BMV-712 and newer, Lynx Shunt VE.Can, Lynx Ion BMS.
+  * All Victron MPPT Solar Charge Controllers
-Requirements:
+Required components:
   * Battery system.
   * Victron inverter/charger.
@@ Line 930: / Line 934: @@
   * [[https://docs.victronenergy.com/gx/mfd-garmin.html|Instructions for Garmin MFDs]]
   * [[venus-os:mfd-navico|Instructions for Navico MFDs]] (Simrad, B&D, Lowrance)
+  * [[venus-os:mfd-raymarine|Instructions for Raymarine]] - Note support on Raymarine MFDs is pending a Raymarine firmware update. [[https://www.victronenergy.com/blog/|Subscribe to our blog (link at the bottom)]], or for direct customers, monitor our weekly e-mail, to be informed about that release.
-Raymarine: support on Raymarine MFDs is pending a Raymarine firmware update. [[https://www.victronenergy.com/blog/|Subscribe to our blog (link at the bottom)]], or for direct customers, monitor our weekly e-mail, to be informed about that release.
 Furuno: support on Furuno MFDs is in the pipeline. There is no expected date of availability.
@@ Line 951: / Line 955: @@
 ===== DISQUS =====
 ~~DISQUS~~