User Tools

Site Tools


ccgx:ccgx_faq

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
ccgx:ccgx_faq [2019-06-06 15:54]
mvader [Q24: What is Error #42?]
ccgx:ccgx_faq [2019-08-15 12:34]
guy_stewart replace venus-device with GX device
Line 157: Line 157:
  
 ==== Q20: Issues with Multi not starting when CCGX is connected / Caution when powering the CCGX from the AC-out terminal of a VE.Bus Inverter, Multi or Quattro ==== ==== Q20: Issues with Multi not starting when CCGX is connected / Caution when powering the CCGX from the AC-out terminal of a VE.Bus Inverter, Multi or Quattro ====
-If you power the CCGX from an AC adaptor connected to the AC-out port of any VE.Bus product (Inverter, Multi or Quattro), then a deadlock ​will occur after the VE.Bus products are powered-down for any reason (after any operational fault or during a black start). The VE.Bus devices will not boot-up until the CCGX has power ...but the CCGX will not boot-up until //it// has power. See FAQ for more information about this.+ 
 +Make sure that the GX device and MultiPlus is running the latest firmware version.  
 + 
 +If you power the CCGX from an AC adaptor connected to the AC-out port of any VE.Bus product (Inverter, Multi or Quattro), then a deadlock ​can occur after the VE.Bus products are powered-down for any reason (after any operational fault or during a black start). The VE.Bus devices will not boot-up until the CCGX has power ...but the CCGX will not boot-up until //it// has power. See FAQ for more information about this.
  
 This deadlock can be rectified by briefly unplugging the CCGX VE.Bus cable at which point you will observe the VE.Bus products will immediately begin to boot-up. This deadlock can be rectified by briefly unplugging the CCGX VE.Bus cable at which point you will observe the VE.Bus products will immediately begin to boot-up.
Line 166: Line 169:
    
 Cutting/​Removing pin 7 of the VE.Bus cable to the CCGX (brown/​white according to standard RJ45 ethernet cable colour coding) allows the VE.Bus products to start up without waiting for the CCGX to boot up first. Cutting/​Removing pin 7 of the VE.Bus cable to the CCGX (brown/​white according to standard RJ45 ethernet cable colour coding) allows the VE.Bus products to start up without waiting for the CCGX to boot up first.
 +
 +Note that when using a Redflow ZBM2/ZCell battery, pin 7 should be cut even if the CCGX is DC powered, to avoid the same deadlock at times when the Redflow battery cluster is at 0% SoC.
  
 {{:​ccgx:​ccgx_pin7.jpg?​direct&​400|}} {{:​ccgx:​ccgx_pin7.jpg?​direct&​400|}}
  
 The //​disadvantage//​ of cutting pin 7 is that switching the VE.Bus device off will be less effective: although it will stop charging and inverting, it will still be in standby mode and therefore drawing more current from the battery than if pin 7 had been left in place. Typically this is only relevant in Marine or Automotive systems where it's normal to regularly switch the VE.Bus device off. For those types of systems we recommend that you do not cut pin 7, but simply power the CCGX from the battery. The //​disadvantage//​ of cutting pin 7 is that switching the VE.Bus device off will be less effective: although it will stop charging and inverting, it will still be in standby mode and therefore drawing more current from the battery than if pin 7 had been left in place. Typically this is only relevant in Marine or Automotive systems where it's normal to regularly switch the VE.Bus device off. For those types of systems we recommend that you do not cut pin 7, but simply power the CCGX from the battery.
 +
 ==== Q21: I love Linux, programming,​ Victron and the Color Control GX. Can I do more? ==== ==== Q21: I love Linux, programming,​ Victron and the Color Control GX. Can I do more? ====
  
Line 178: Line 184:
 Typic the following address into the web browser of a device connected to the same network. Using this address as a template: ​ Typic the following address into the web browser of a device connected to the same network. Using this address as a template: ​
 http://​[ip-here]/​logo.php ​ (inserting your device’s IP address between the square brackets). ​ http://​[ip-here]/​logo.php ​ (inserting your device’s IP address between the square brackets). ​
-The IP address can be found by going to Settings > Ethernet or Wifi. Once the page is loaded, Choose an image file from your device. Re-boot the [[venus-os:​start|Venus-device]].+The IP address can be found by going to Settings > Ethernet or Wifi. Once the page is loaded, Choose an image file from your device. Re-boot the [[venus-os:​start|GX device]].
  
 ==== Q23: Multi restarts all the time (after every ~10sec) ==== ==== Q23: Multi restarts all the time (after every ~10sec) ====
Line 199: Line 205:
 ===== DISQUS ===== ===== DISQUS =====
 ~~DISQUS~~ ~~DISQUS~~
- 
ccgx/ccgx_faq.txt · Last modified: 2019-08-15 12:34 by guy_stewart