ccgx:ccgx_faq
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
ccgx:ccgx_faq [2019-05-17 16:18] – [Q1: I cannot switch my Multi/Quattro system on or off] john_r | ccgx:ccgx_faq [2019-06-14 07:35] – [Q20: Issues with Multi not starting when CCGX is connected / Caution when powering the CCGX from the AC-out terminal of a VE.Bus Inverter, Multi or Quattro] guy_stewart | ||
---|---|---|---|
Line 157: | Line 157: | ||
==== Q20: Issues with Multi not starting when CCGX is connected / Caution when powering the CCGX from the AC-out terminal of a VE.Bus Inverter, Multi or Quattro ==== | ==== Q20: Issues with Multi not starting when CCGX is connected / Caution when powering the CCGX from the AC-out terminal of a VE.Bus Inverter, Multi or Quattro ==== | ||
- | If you power the CCGX from an AC adaptor connected to the AC-out port of any VE.Bus product (Inverter, Multi or Quattro), then a deadlock will occur after the VE.Bus products are powered-down for any reason (after any operational fault or during a black start). The VE.Bus devices will not boot-up until the CCGX has power ...but the CCGX will not boot-up until //it// has power. See FAQ for more information about this. | ||
- | This deadlock can be rectified by briefly unplugging the CCGX VE.Bus cable at which point you will observe the VE.Bus products will immediately begin to boot-up. | + | Make sure that the GX device and MultiPlus is running |
- | + | ||
- | This deadlock can be avoided in two ways: | + | |
- | * Power the CCGX from the battery; or | + | |
- | * Cut pin 7 in the VE.Bus cable connected to the CCGX | + | |
- | + | ||
- | Cutting/ | + | |
- | + | ||
- | {{: | + | |
- | + | ||
- | The // | + | |
==== Q21: I love Linux, programming, | ==== Q21: I love Linux, programming, | ||
Line 183: | Line 172: | ||
Please check the remote switch connection on the Multi control PCB. There should be a wire bridge between the left and middle terminal. The CCGX switches a line which enables the power of the Multi control board. After 10 seconds this line is released and the Multi should take over from there. When the remote switch connection is not wired the Multi is unable to take over it's own supply. The CCGX will retry, the Multi will boot and after 10 seconds stop, and so on. | Please check the remote switch connection on the Multi control PCB. There should be a wire bridge between the left and middle terminal. The CCGX switches a line which enables the power of the Multi control board. After 10 seconds this line is released and the Multi should take over from there. When the remote switch connection is not wired the Multi is unable to take over it's own supply. The CCGX will retry, the Multi will boot and after 10 seconds stop, and so on. | ||
+ | |||
+ | ==== Q24: What is Error #42? ==== | ||
+ | |||
+ | If the GX Device shows an Error 42 - Hardware fault. In that case, the flash storage on the device is corrupt. As a result, settings will not be saved (rebooting resets back to default) and other problems will rise. | ||
+ | |||
+ | This error is not recoverable in the field or by repair departments. Contact your dealer for a replacement. | ||
+ | |||
+ | Firmware versions until v2.30 did not report the error. Since v2.30; its visible on the device itself (in the GUI) and on the VRM Portal. | ||
===== GPL Note ===== | ===== GPL Note ===== |
ccgx/ccgx_faq.txt · Last modified: 2021-02-05 11:34 by marmour