Differences

This shows you the differences between two versions of the page.

--- battery_compatibility:can-bus_bms-cable [2017-12-13 17:29] – created mvader
+++ battery_compatibility:can-bus_bms-cable [2023-12-14 07:05] (current) – [1. Selecting the right cable] warwickchapman
@@ Line 1: / Line 1: @@
 ====== VE.Can to CAN-bus BMS cables manual ======
-===== 1. Introduction =====
+Use these [[https://www.victronenergy.com/cables/ve-can-to-can-bus-bms|VE.Can to CAN-bus cables]] to connect a CAN-bus enabled battery to a [[https://www.victronenergy.com/live/venus-os:start|GX device]].
-Use this cable to connect a CAN-bus enabled battery to a Victron system.
-The side labeled 'CAN-bus BMS' plugs into the battery. The other sie, labeled 'VE.Can' must be plugged into the VE.Can port of the Venus-device.
-There are two types, each with different pinning. Some brands of batteries require a Type A. Other brands require the Type B cable.
+===== 1. Selecting the right cable =====
-Batteries that require the Type A cable:
+=== ASS030710018 - VE.Can to CAN-bus BMS type A Cable 1.8m ===
   * BYD B-Box
+  * Pylontech US2000C/US3000C/UP5000/Force-L
-Batteries that require the Type B cable:
+=== ASS030720018 - VE.Can to CAN-bus BMS type B Cable 1.8m ===
-  * LG Chem Resu
+  * AXIstorage 7S/9S
-  * AXIstorage
   * BMZ
-  * Pylontech
+  * BSLBATT Lithium battery
+  * Hubble Lithium
+  * LG Chem Resu
+  * Pylontech US2000/US3000/UP2500
+  * Solar MD BMS EX
-===== 2. Pin-out =====
+=== ASS030064950 RJ45 UTP Cable (Standard Ethernet) ===
+  * Bluenova Energy Storage
+  * Cegasa eBick
+  * Freedom Won
+  * MG Energy Systems
-For the do-it-yourselvers:
+=== Custom (See Battery Documentation) ===
+  * Exide
+  * SolarMD Logger V2
-==== 2.1 Type A ====
+===== 2. Installation =====
+The side labeled 'CAN-bus BMS' plugs into the battery. The other side, labeled 'VE.Can' must be plugged into either the VE.Can port of the GX device, or the BMS-Can port.
+Both port types (VE.Can and BMS-Can) on a GX Device can be configured for use with a CAN-bus BMS connected third party battery.
+For configuration, see the manual specific to the brand of battery you are using.
+===== 3. Pin-out =====
+In some cases it might be needed to make the cable at the location. Find below the pin-outs. Make sure to very carefully test the cable after crimping it. Self-made cables are very often the causes of very hard to diagnose problems.
+==== 3.1 Type A ====
 ^ Function ^ Victron VE.Can side ^ Battery side ^
 | GND      | Pin 3        | Pin 6       |
@@ Line 29: / Line 49: @@
 | CAN-H	   | Pin 7        | Pin 4       |
-==== 2.2 Type B ====
+==== 3.2 Type B ====
 ^ Function ^ Victron VE.Can side ^ Battery side ^
@@ Line 36: / Line 56: @@
 | CAN-H	   | Pin 7        | Pin 4         |
-===== DISQUS =====
-~~DISQUS~~