Differences

This shows you the differences between two versions of the page.

--- battery_compatibility:bmz_ess [2019-01-22 10:16] – external edit 127.0.0.1
+++ battery_compatibility:bmz_ess [2019-09-09 08:34] – alexander.joist_ibc-solar.co.za
@@ Line 1: / Line 1: @@
-====== Victron & BMZ ESS 3.0 / ESS 7.0 =====
+====== Victron & BMZ ESS 7.0 / ESS 9.0 / ESS X=====
-The combination of Victron products with the BMZ ESS 7.0 battery has been tested and certified by the R&D departments. The combination is actively supported by both companies.
+The combination of Victron products with the BMZ ESS battery has been tested and certified by the R&D departments. The combination is actively supported by both companies.
 ==== 1. Introduction ====
 === 1.1 Compatible Victron products ===
-All 48V Multis and Quattros. And always a [[venus-os:start|Venus-device]] is necessary in the system, since that has the canbus port which is used for the (required!) communication between the ESS battery and the Victron system.
+All 48V Multis and Quattros. And always a [[venus-os:start|GX device]] is necessary in the system, since that has the canbus port which is used for the (required!) communication between the ESS battery and the Victron system.
 === 1.2 Notes ===
@@ Line 19: / Line 19: @@
 {{ :battery_compatibility:hub4-1phase-bmzess.png?nolink |}}
-==== 2. Venus-device needed ====
+==== 2. GX device needed ====
-To use the BMZ ESS in Victron system, it is necessary to use a Color Control GX or Venus GX. On first commissioning an external power supply (Not the 48V from the BMZ-Battery) is needed. The CCGX/VGX sends a keep alive signal to the BMZ ESS via canbus. This will only be send once the canbus baud rate is changed (see 5. [[venus-os:start|Venus-device]] Configuration). Without it, the battery will have a communication fault and shut down after 10sec.
+To use the BMZ ESS in Victron system, it is necessary to use a Color Control GX or Venus GX. On first commissioning an external power supply (Not the 48V from the BMZ-Battery) is needed. The CCGX/VGX sends a keep alive signal to the BMZ ESS via canbus. This will only be send once the canbus baud rate is changed (see 5. [[venus-os:start|GX device]] Configuration). Without it, the battery will have a communication fault and shut down after 10sec.
 ==== 3. Wiring of communication cables ====
-Use the //VE.Can to CAN-bus BMS type B Cable//, part number ASS030720018. Plug the side which is labeled Battery BMS into the BMZ BMS. Plug the side labeled Victron VE.Can into the [[venus-os:start|Venus-device]].
+Use the //VE.Can to CAN-bus BMS type B Cable//, part number ASS030720018. Plug the side which is labeled Battery BMS into the BMZ BMS. Plug the side labeled Victron VE.Can into the [[venus-os:start|GX device]].
-Then, plug a [[https://www.victronenergy.com/accessories/ve-can-rj45-terminator|VE.Can terminator]] in the other VE.Can socket on the [[venus-os:start|Venus-device]]. Two VE.Can terminators are included with the package of the CCGX as an accessory, only one is used. Keep the other one as a spare.
+Then, plug a [[https://www.victronenergy.com/accessories/ve-can-rj45-terminator|VE.Can terminator]] in the other VE.Can socket on the [[venus-os:start|GX device]]. Two VE.Can terminators are included with the package of the CCGX as an accessory, only one is used. Keep the other one as a spare.
 More information about the cable can be found in [[battery_compatibility:can-bus_bms-cable|its manual]].
-Without properly connecting this cable, the battery will stop charging/discharging after several minutes. Also, the battery will not show up on the display of the [[venus-os:start|Venus-device]].
+Without properly connecting this cable, the battery will stop charging/discharging after several minutes. Also, the battery will not show up on the display of the [[venus-os:start|GX device]].
 ==== 4. VEConfigure settings ====
@@ Line 37: / Line 37: @@
   - Check "Enable battery monitor"
   - Enter the battery capacity:
-    - BMZ ESS 3.0 - 121.5 Ah
+    - BMZ ESS 7.0 - 121.5 Ah
-    - BMZ ESS 7.0 - 156.6 Ah
+    - BMZ ESS 9.0 - 156.6 Ah
     - BMZ ESS X - 186.3 Ah
   - The other parameters ("State of charge when bulk finished" and "Charge efficiency") can be left to their default setting. They are not used in this setup.
@@ Line 63: / Line 63: @@
-==== 5. Venus-device Configuration ====
+==== 5. GX device Configuration ====
-  * Select the //CAN-bus BMS (500 kbits/s)// CAN-profile in the [[venus-os:start|Venus-device]]. Menu path: //Settings -> Services -> CAN-profile//. Note that this changes the function of a VE.Can port: it is not possible to connect both VE.Can products and a BMZ battery together on a Color Control GX. Is is possible on the Venus GX
+  * Select the //CAN-bus BMS (500 kbits/s)// CAN-profile in the [[venus-os:start|GX device]]. Menu path: //Settings -> Services -> CAN-profile//. Note that this changes the function of a VE.Can port: it is not possible to connect both VE.Can products and a BMZ battery together on a Color Control GX. Is is possible on the Venus GX
   * After properly wiring and setting up, the BMZ ESS will be visible as a battery in the device list:{{ :battery_compatibility:generic_battery_menu.png?nolink&290 | }}